This article is about a simple 0-100°C digital thermometer with 1°C
resolution using 8051. The circuit is based on LM35 analog temperature
sensor, ADC0804 and AT89S51 microcontroller. LM35 is an analogue
temperature sensor IC which can measure a temperature range of -55 to
150°C. Its output voltage varies 10mV per °C change in temperature.
For example, if the temperature is 32°C, the output
voltage will be 32 x 10mV = 320mV. ADC 0804 is used to convert the
analogue output voltage of the LM35 to a proportional 8 bit digital
value suitable for the microcontroller. The microcontroller accepts the
output of ADC, performs necessary manipulations on it and displays it
numerically on a 2 digit seven segment LED display.
Out put of the LM35 is connected to the +Vin (pin 6) of the ADC0804.
Resistor R13 and preset R14 is used to provide an external reference
voltage of 1.28V to the Vref/2 pin ( pin 9) of the ADC0804 and with
this reference voltage, the step size of the ADC will be 10mV and span
will be 0-1 V. This means that for a 10mV input the digital out of ADC
will be 1 (1 in decimal also), for 20mV it will be 10 (2 in decimal),
for 30mV it will be 11 (3 in decimal) and so on. The microcontroller
accepts this data and puts it on the seven segment display.
Circuit diagram.
Digital thermometer using 8051
Digital out of the ADC (D0 to D7) are connected to P1 (P1.0 to P1.7) of
the microcontroller. This is the line through which the microcontroller
accepts data from the ADC. The control pins CS, RD, WR and INTR are
connected to P3.7, P3.6, P3.5 and P3.4 of the microcontroller. This is
the data path through which the microcontroller sends chip select (CS),
read (RD) write (WR) signals to the ADC and receives INTR signal from
the ADC. Data lines (a to h) of the multiplexed seven segment display
are interfaced to P0 (P0.0 to P0.7) of the microcontroller. Activation
signals for the segment driver transistors Q1 and Q2 are available from
P3.2 and P3.1 pins of the microcontroller.
Before attempting this circuit go through these articles Voltmeter using 8051 , Interfacing ADC to 8051 ,Interfacing seven segment display to 8051.
Program.
ORG 00H
MOV P1,#11111111B // initializes P1 as input port
MOV P0,#00000000B // initializes P0 as output port
MOV P3,#00000000B // initializes P3 as output port
MOV DPTR,#LABEL // loads the address of "LABEL" to DPTR
MAIN: MOV R4,#250D // loads register R4 with 250D
CLR P3.7 // makes Cs=0
SETB P3.6 // makes RD high
CLR P3.5 // makes WR low
SETB P3.5 // low to high pulse to WR for starting conversion
WAIT: JB P3.4,WAIT // polls until INTR=0
CLR P3.7 // ensures CS=0
CLR P3.6 // high to low pulse to RD for reading the data from ADC
MOV A,P1 // moves the digital output of ADC to accumulator A
MOV B,#10D // load B with 10D
DIV AB // divides the content of A with that in B
MOV R6,A // moves the quotient to R6
MOV R7,B // moves the remainder to R7
DLOOP:SETB P3.2 // sets P3.2 which activates LED segment 1
MOV A,R6 // moves the quotient to A
ACALL DISPLAY // calls DISPLAY subroutine
MOV P0,A // moves the content of A to P0
ACALL DELAY // calls the DELAY subroutine
CLR A // clears A
MOV A,R7 // moves the remainder to A
CLR P3.2 // deactivates LED segment 1
SETB P3.1 // activates LED segment 2
ACALL DISPLAY
MOV P0,A
ACALL DELAY
CLR A
CLR P3.1 // deactivates LED segment 2
DJNZ R4,DLOOP // repeats the loop "DLOOP" until R4=0
SJMP MAIN // jumps back to the main loop
DELAY: MOV R3,#255D // produces around 0.8mS delay
LABEL1: DJNZ R3,LABEL1
RET
DISPLAY: MOVC A,@A+DPTR // converts A's content to corresponding digit drive pattern
RET
LABEL: DB 3FH // LUT (look up table) starts here
DB 06H
DB 5BH
DB 4FH
DB 66H
DB 6DH
DB 7DH
DB 07H
DB 7FH
DB 6FH
END
No comments:
Post a Comment